CLICK TO ENLARGE	Gather the tools needed to assemble the trailer. •  11mm, 13mm, 17mm, 19mm, 21mm, 24mm sockets w/ extension •  11mm, 13mm, 17mm, 19mm, 24mm open end wrench(s)
CLICK TO ENLARGE	Open & remove all parts from on top of the trailer frame VERY IMPORTANT: Locate and remove the envelope that has the Certificate of Origin inside and put it with the Owner's Manual for safe keeping. Locate the bolts bag and empty contents into a contained area
CLICK TO ENLARGE	Tear the four corners of the bottom box which has the trailer frame sitting on it. This will result in the box laying flat.
CLICK TO ENLARGE	Springs, Axles, Tires, and Fenders
CLICK TO ENLARGE	Axle Spring Assembly
CLICK TO ENLARGE	Place a block under each corner of the trailer frame. This will result in the frame being raised off the ground. Make sure that the bottom of the trailer is facing upwards so that the springs, fenders, axle, and tongue can be mounted. Lay springs in spring track with spring eye facing towards front of trailer frame and the spring spoon facing the rear of the trailer.
CLICK TO ENLARGE	To correctly place fenders into position, make sure the longer mount bracket is facing the rear of trailer frame.
CLICK TO ENLARGE	Using parts B-13, 14, 15 securely attach springs and fenders to the trailer frame.
CLICK TO ENLARGE	Completed Assembly
CLICK TO ENLARGE	Lay axle across springs with the nipple on each spring into the nipple hole on the axle
CLICK TO ENLARGE	Using parts B-9, 10 (“U” bolts and spring plate) securely attach the axle to both springs
CLICK TO ENLARGE	A grease zerk fitting is located behind each wheel which only requires the use of a grease gun. Caution: DO NOT over tighten nut. The hub must turn freely and without play
CLICK TO ENLARGE	Attach parts A-9 (the wheels) to the axle with parts B-12 (lug nuts). Refer to owner's manual for proper torque (80 lbs.) and maintenance
CLICK TO ENLARGE	Frame with axles, fenders, springs, and wheels attatched.
CLICK TO ENLARGE	Lay part A-2 (tongue) into load bearing guide, making sure the tongue stand is pointed up. Attach tongue with part B-3, 4, 5
CLICK TO ENLARGE	Connect the 12v trailer frame wire plug to the 12v tongue wire plug
CLICK TO ENLARGE	Connect the 12v trailer frame wire plug to the 12v tongue wire plug
CLICK TO ENLARGE	Connect the 12v trailer frame wire plug to the 12v tongue wire plug
CLICK TO ENLARGE	L Bolt and Pin
CLICK TO ENLARGE	Attach part B-7, 8 (removable L bolt & pin)to secure the front of tongue to trailer frame
CLICK TO ENLARGE	Trailer with Tongue attached
CLICK TO ENLARGE	USE EXTREME CAUTION: Using at least (2) strong bodied people, safely flip the trailer over by standing the trailer on end (its rear frame) and carefully flipping it over to support itself on the wheels and the tongue stand. Do not attempt this if you do not have; 1.) Adequate clearance above and from side to side or 2.) Enough man power that can SAFELY handle the weight of the trailer when flipping it over (refer to figure 4)
CLICK TO ENLARGE	A-12 Tail Light Bracket Parts B-23, 24, 24a Identify which light is the right side and left side by looking at the bottom of the lights. The left light (driver's side) has a clear lens in the bottom for the illumination of a license plate.
CLICK TO ENLARGE	Mount part A-12 (tail light bracket) to rear side of trailer. Make sure that the large opening is facing the rear of the trailer. Using parts B-23, 24, 24a mount the brackets securely to the trailer frame. The light brackets can be mounted in either a 1.) Flush position if the trailer is to be used as a flat bed and 2.) Extended height position if you are going to use the trailer with the sides on. PLEASE NOTE: Make sure the 12v wires are pulled through the bracket and not pinched when mounting the brackets.
CLICK TO ENLARGE	Properly attach the 12v wires and ground wire to the back of the tail light(s). Using wire connectors, connect color to color and make sure that the ground wire is bolted down to the light / light bracket assembly.
CLICK TO ENLARGE	Completed Wiring
CLICK TO ENLARGE	Parts B-1, 2
CLICK TO ENLARGE	Attach A-1 (2” coupler) securely to the tongue using part B-1, 2
CLICK TO ENLARGE	Coupler attached to tongue
CLICK TO ENLARGE	Place safety chain through tongue stand and secure it in accordance of your specific state laws (may need 1 or 2 bolts securing it to the tongue stand)
CLICK TO ENLARGE	Trailer with rear lights, tongue, and coupler
CLICK TO ENLARGE	Side Panel Bolts
CLICK TO ENLARGE	Mount the side panels. Make sure the frame posts are on the exposed (outside) of the trailer, with the smooth metal on the inside
CLICK TO ENLARGE	Attach and securely tighten the parts A-5 (side panels) to the trailer using parts B-17, 18, 19 and B-20, 21, 22
CLICK TO ENLARGE	Mount the front & back drop gates properly. Secure the top corners of each drop gate using the quick release lever that is on each side rail Attach parts A3 (front and back drop gate) to the trailer with b-6
CLICK TO ENLARGE	Completed trailer